1783-ETAP1F 3端口enet 以太网 I/P 网络

☆型号：1783-ETAP1F 3端口enet  以太网 I/P 网络

【产品详情】

Allen-Bradley ETAP1F 是一种用于以太网 I/P 网络的工业网络设备。该产品本质上是一个以太网交换机，内置两 （2） 个铜缆端口和一 （1） 个光纤接口。该模块非常适合用于连接 Allen-Bradley 设备，例如控制器、通信和可视化设备，以实现工业认可的自动化系统。

1783-ETAP1F 的双铜端口支持 10/100 Mbps 和自动协商功能，并支持全双工或半双工模式，而 1783-ETAP1F 的单光纤端口也能够达到 100Mbps，但是，它支持更长的通信距离，对电气噪声和干扰的抗扰度更高。

1783-ETAP1F 是一款外部安装的交换机，不需要背板即可安装，但是，需要适当的外壳来容纳设备，以保护可能损坏模块的工业元件。1783-ETAP1F 的电源要求为 24VDC（标称），适用范围为 20.4...27.6V 直流。该设备可以使用标准DIN导轨安装，也可以直接安装到外壳的安装板上。它支持水平和垂直安装方向，水龙头底部的最小间隙为 7.62 厘米（3 英寸），水龙头其余侧面的最小间隙为 2.54 厘米（1 英寸）。对于光缆入口，建议至少 5.08 厘米或 2 英寸，以符合光纤电缆的必要弯曲半径。

1783-ETAP1F 具有内置诊断 LED，例如 OK 和 Link1 以及 Link 2 状态指示灯。

此交换机通过嵌入式两 （2） 个铜缆端口和一 （1） 个光纤接口提供以太网连接。

Allen-Bradley/Rockwell Automation 1783-ETAP1F 以太网/IP 交换机的优点之一是它使用户能够将铜缆和光纤网络结合起来。光纤网络理想地用于覆盖点之间的更长距离，并且不易受到电噪声的影响，从而提供更清晰的信号。

☆型号：1783-ETAP1F 3端口enet  以太网 I/P 网络

【英文介绍】

The Allen-Bradley ETAP1F is an industrial networking device for Ethernet I/P networks. The product is essentially an Ethernet switch with two (2) copper cable ports and one (1) optical fiber interface built in. The module is ideal for connecting Allen-Bradley devices, such as controllers, communication and visualization devices, to achieve industry-approved automation systems.

The 1783-ETAP1F's dual copper port supports 10/100 Mbps and auto-negotiation and supports full-duplex or half-duplex modes, while the 1783-ETAP1F's single fiber port is also capable of up to 100Mbps, however, it supports longer communication distances and is more resistant to electrical noise and interference.

The 1783-ETAP1F is an externally mounted switch that can be installed without a backplane, however, a proper housing is required to house the device to protect industrial components that could damage the module. The 1783-ETAP1F has a power supply requirement of 24VDC (nominal) and an application range of 20.4... 27.6V DC. The device can be mounted using standard DIN rails or directly onto the mounting plate of the housing. It supports both horizontal and vertical mounting directions, with a minimum clearance of 7.62 cm (3 in) at the bottom of the faucet and 2.54 cm (1 in) on the remaining sides of the faucet. For cable intakes, a minimum of 5.08 cm or 2 inches is recommended to conform to the necessary bending radius of the fiber optic cable.

The 1783-ETAP1F has built-in diagnostic leds such as OK and Link1 and Link 2 status indicators.

This switch provides Ethernet connectivity through two (2) embedded copper cable ports and one (1) optical fiber interface.

One of the advantages of the Allen-Bradley/Rockwell Automation 1783-ETAP1F Ethernet /IP switch is that it enables users to combine copper and fiber networks. Fiber optic networks are ideal for covering longer distances between points and are less susceptible to electrical noise, providing a clearer signal.

☆型号：1783-ETAP1F 3端口enet  以太网 I/P 网络

【其他型号推荐】