IC200PBI001 网络接口单元或NIU 控制 I/O 模块

【产品详情】

IC200PBI001模块是GE Fanuc的Versamax网络接口单元或NIU。它用于控制 I/O 模块。网络接口单元由直接安装在单元上的电源供电。它消耗 250 伏总线的 5 毫安电流和 10.3 伏总线的 3 毫安电流。单个网络单元中共有 64 个 I/O 模块。可以使用扩展机架进行扩展。它带有从 1 到 125 的 Profibus 网络地址。网络数据速率范围为 9.6 Kbaud 至 12 Mbaud。NIU 会自动检测数据速率。IC200PBI001 NIU 使用 5 字节的用户诊断数据内存运行。该装置的前面板带有 4 个 LED 指示灯，用于显示设备的电源、运行状况、故障和网络状态，以及一个强制 LED。

IC200PBI001模块的固件可以轻松更新。在更新过程中，必须将控制器切换到采场模式，并且应断开网线与NIU的连接。它一次可以处理 375 字节的 I/O 数据。正面有一个旋转开关，可以使用一字螺丝刀进行调节。此开关用于选择 1-125 范围内的地址。IC200PBI001 NIU易于安装，只需点击DIN导轨即可。可以使用闩锁将电源连接到 NIU。连接器和闩锁应匹配并卡在一起。它支持多达 32 个站点，而无需使用中继器。它配备了一个 9 针 D-sub 连接器。

IC200PBI001是 Profibus-DP 网络接口单元 （NIU），在 GE 为 VersaMax 系列设计的 Profibus-DP 网络上充当从站。IC200PBI001充当一组 I/O 模块的控制器。该模块使用提供的电源运行，该电源直接安装在 NIU 上。

IC200PBI001的网络地址为 1 到 125，网络数据速率为 9.6Kbaud 至 12Mbaud，可自动检测。最多有 375 字节的 I/O 数据，最多有 244 个字节的输入或 244 字节的输出。IC200PBI001每个 NIU 可以控制 64 个 I/O 模块。

IC200PBI001配备200个LED指示灯，帮助用户监控NIU的电源和状态。通电后，PWR LED 将呈绿色。当 OK LED 为绿色时，固件正常工作。如果 FAULT LED 呈琥珀色，则表明 NIU 在内部或 I/O 模块中发现了故障。网络 LED 可以是绿色、琥珀色或熄灭，具体取决于以下内容。如果为绿色，则表示 I/O 已成功在网络上传输。如果 LED 呈琥珀色，则主设备发送的配置被拒绝。当网络 LED 熄灭时，未检测到与主设备的通信。FORCE LED 指定是否存在任何强制 I/O 值。此版本的 IC001PBI<> Profibus NIU 与所有 VersaMax 高密度模拟模块兼容。

IC200PBI001 Profibus-DP 网络接口单元或 NIU 是 GE Fanuc 的产品，属于 VersaMax 产品系列。它用作 Profibus-DP 网络上的从设备，并用作一组输入和输出模块的控制器。该模块由直接安装在其上的外部提供的电源运行。IC200PBI001 NIU 的网络地址为 1 到 125，网络数据速率为 9.6 Kbaud 至 12 Mbaud，可自动检测。它具有 375 字节的全 I/O 数据容量，输入额定值高达 244 字节，输出额定值高达 244 字节。该网络接口单元一次最多可控制 64 个输入和输出。

GE Fanuc IC200PBI001 网络接口单元具有 5 个 LED 指示灯，可帮助操作员监控电源以及 NIU 的状态。如果通电，“PWR”LED 指示灯变为绿色，当“OK”LED 指示灯变为绿色时，则表示固件正常工作。当“FAULT”LED 指示灯呈琥珀色时，表示 IC200PBI001 NIU 存在内部故障。此外，“NETWORK”LED 指示灯可以呈琥珀色或绿色亮起或熄灭。绿灯表示 I/O 数据在网络上传输成功。琥珀色指示灯表示主设备发送的配置被拒绝。当“NETWORK”LED 指示灯熄灭时，表示与主设备没有通信。此外，还有一个“FORCE”LED 指示灯，用于指定是否存在强制输入和输出值。IC200PBI001 Profibus NIU 与所有 VersaMax 高密度模拟模块完美匹配。

IC200PBI001 网络接口单元或NIU 控制 I/O 模块

【英文介绍】

The IC200PBI001 module is GE Fanuc's Versamax network interface unit or NIU. It is used to control the I/O module. The network interface unit is powered by a power supply installed directly on the unit. It consumes 5 mA of a 250 volt bus and 3 mA of a 10.3 volt bus. A single network unit has a total of 64 I/O modules. You can use an extension rack for expansion. It carries a Profibus network address from 1 to 125. The network data rate ranges from 9.6 Kbaud to 12 Mbaud. NIU detects the data rate automatically. IC200PBI001 NIU runs in memory with 5 bytes of user diagnostic data. The front panel of the device has 4 LED indicators for the power, health, failure and network status of the device, as well as a forced LED.

The firmware of the IC200PBI001 module can be easily updated. During the update process, the controller must be switched to stope mode and the network cable should be disconnected from the NIU. It can process 375 bytes of I/O data at a time. There is a rotary switch on the front that can be adjusted using a flat-head screwdriver. This switch is used to select addresses in the range 1-125. The IC200PBI001 NIU is easy to install with just a click on the DIN rail. The power supply can be connected to the NIU using a latch. Connectors and latches should match and snap together. It supports up to 32 sites without the use of Repeaters. It comes with a 9-pin D-sub connector.

The IC200PBI001 is a Profibus-DP Network interface Unit (NIU) that acts as a slave station on GE's Profibus-DP network designed for the VersaMax family. The IC200PBI001 acts as a controller for a set of I/O modules. The module runs on the supplied power supply, which is installed directly on the NIU.

The IC200PBI001 has network addresses from 1 to 125 and network data rates from 9.6Kbaud to 12Mbaud for automatic detection. Up to 375 bytes of I/O data, up to 244 bytes of input or 244 bytes of output. IC200PBI001 Each NIU can control 64 I/O modules.

The IC200PBI001 is equipped with 200 LED indicators to help users monitor the power and status of NIU. When powered on, the PWR LED will appear green. When the OK LED is green, the firmware works normally. If the FAULT LED is amber, NIU has found a fault inside or in the I/O module. The network LED can be green, amber, or off, depending on the following. If the value is green, I/ OS have been successfully transmitted on the network. If the LED is amber, the configuration sent by the master device is rejected. When the network LED is off, no communication with the main device is detected. FORCE LED Specifies whether any forced I/O values exist. This version of IC001PBI<> Profibus NIU is compatible with all VersaMax high-density analog modules.

The IC200PBI001 Profibus-DP Network Interface Unit, or NIU, is a product of GE Fanuc and belongs to the VersaMax product family. It is used as a slave device on the Profibus-DP network and as a controller for a set of input and output modules. The module is operated by an external power supply mounted directly on it. The network address of IC200PBI001 NIU ranges from 1 to 125, and the network data rate ranges from 9.6 Kbaud to 12 Mbaud. It has 375 bytes of full I/O data capacity with input ratings up to 244 bytes and output ratings up to 244 bytes. The network interface unit can control up to 64 inputs and outputs at a time.

The GE Fanuc IC200PBI001 network interface unit has 5 LED indicators to help the operator monitor the status of the power supply and NIU. If the power is on, the "PWR" LED indicator turns green, and when the "OK" LED indicator turns green, the firmware is working normally. If the FAULT LED indicator is amber, the IC200PBI001 NIU has an internal fault. In addition, the "NETWORK" LED indicator light can be lit up or off in amber or green. The green light indicates that I/O data is successfully transmitted on the network. The amber indicator indicates that the configuration sent by the master device is rejected. When the "NETWORK" LED is off, it indicates that there is no communication with the main device. In addition, there is a "FORCE" LED indicator that specifies whether there are forced input and output values. The IC200PBI001 Profibus NIU is a perfect match for all VersaMax high-density analog modules.

IC200PBI001 网络接口单元或NIU 控制 I/O 模块

【其他型号推荐】