IC200NDD010 系统控制器 具有很高的效率

【产品详情】

IC200NDD010控制器是用于 Versamax 系列的 NANO PLC 系统控制器。它由 GE Fanuc 制造。它是一款 10 点 PLC 设备，具有 6 个输入，额定电压为 12 伏直流电。它有 4 个输出，额定电压为 12 伏直流电。这种PLC设备主要用于工业自动化。它具有很高的效率，而且经久耐用。它外形小巧，重量仅为 1 磅。NANO PLC 的 10 个 I/O 点有自己的 LED 指示灯，用于显示通过每个点的电源流和连接状态。还有 LED 指示灯，即 PLC 正面的“FLD PWR”和“OK”LED 状态。IC200NDD010控制器符合工业标准，可在 I 类 2 级环境中运行。安装区域的环境温度应在 0 到 60 摄氏度之间，以避免热降额或过热。

IC200NDD010是GE设计的VersaMax Nano PLC。IC200NDD010采用+12VDC标称输入电源供电。该IC200NDD010具有 12 个 <>VDC 输入和 <> 个 DC 晶体管输出。

该IC200NDD010具有六个可配置的直流输入，可构建为标准或 HSC 输入，其特性为正或负。如果输入作为标准运行，则这些功能与各种输入设备兼容。包括按钮、限位开关和电子接近开关在内的设备。四个晶体管输出可以创建为正常输出或高速计数器调节的输出。如果输出调节由高速计数器控制，则可以将其配置为脉冲序列和/或脉宽调制 （PWM） 输出。IC200NDD010的输出具有一个公共输入电源 （VC） 和一个公共接地 （COM）。输出能够以额定电流的 8 倍速率驱动高浪涌电流，因此能够切换灯和感性负载。

IC200NDD010的高速计数器输出在开启时具有 9V 的输入电压，在关闭时具有 2.5V 的输入电压。计数器的最大频率为10kHZ，占空比计数脉冲宽度为20%至80%。最多有三个 HSC/PT 和/或 PWM 输出，负载电压为 12V，最大脉冲频率为 5kHz。

GE Fanuc IC200NDD010 PLC系统控制器可以通过使用编程终端或使用控制器上的串行端口将其连接到个人计算机来轻松编程。控制器具有 RS-232 和 RS-485 端口，用于连接各种其他设备。这些串行端口为本地工业网络提供高速数据传输。模块每个点的最大额定电流负载为 0.7 安培。PLC 系统控制器的晶体管输出最大压降为 0.3 V，泄漏关断状态额定值最大为 0.1 毫安。IC200NDD010控制器支持梯形图编程，也可以轻松处理浮点数据和算法。

IC200NDD010 系统控制器 具有很高的效率

【英文介绍】

The IC200NDD010 controller is a NANO PLC system controller for the Versamax family. It is manufactured by GE Fanuc. It is a 10-point PLC device with 6 inputs and is rated at 12 volts DC. It has 4 outputs and is rated at 12 volts DC. This PLC equipment is mainly used in industrial automation. It is highly efficient and durable. It's small and weighs just 1 pound. The NANO PLC's 10 I/O points have their own LED indicators to show the power flow and connection status through each point. There are also LED indicators, namely the "FLD PWR" and "OK" LED status on the front of the PLC. The IC200NDD010 controller meets industry standards and can operate in Class I Level 2 environments. The ambient temperature in the installation area should be between 0 and 60 degrees Celsius to avoid heat derating or overheating.

IC200NDD010 is the VersaMax Nano PLC designed by GE. The IC200NDD010 uses a +12VDC nominal input power supply. The IC200NDD010 has 12 <>VDC inputs and <> DC transistor outputs.

The IC200NDD010 has six configurable DC inputs that can be built as standard or HSC inputs with positive or negative characteristics. If the input runs as standard, these functions are compatible with a variety of input devices. Devices including buttons, limit switches and electronic access switches. Four transistor outputs can be created as normal outputs or as high speed counter regulated outputs. If the output regulation is controlled by a high-speed counter, it can be configured as a pulse train and/or pulse width modulation (PWM) output. The output of the IC200NDD010 has a common input power (VC) and a common ground (COM). The output is capable of driving high surge current at a rate of 8 times the rated current, so it is able to switch lights and inductive loads.

The IC200NDD010's high-speed counter output has an input voltage of 9V when turned on and 2.5V when turned off. The maximum frequency of the counter is 10kHZ, and the duty cycle counting pulse width is 20% to 80%. There are up to three HSC/PT and/or PWM outputs with a load voltage of 12V and a maximum pulse frequency of 5kHz.

The GE Fanuc IC200NDD010 PLC system controller can be easily programmed by using a programming terminal or by connecting it to a personal computer using a serial port on the controller. The controller has RS-232 and RS-485 ports for connecting a variety of other devices. These serial ports provide high-speed data transmission for local industrial networks. The maximum rated current load at each point of the module is 0.7 amps. The PLC system controller has a maximum transistor output voltage drop of 0.3V and a leak off state rating of up to 0.1mA. The IC200NDD010 controller supports ladder diagram programming and can also easily handle floating-point data and algorithms.

IC200NDD010 系统控制器 具有很高的效率

【其他型号推荐】