IC200MDL244 离散输入模块 用户输入与逻辑和框

【产品详情】

IC200MDL244 是一款具有 240 个点的 VersaMax 200 VAC 隔离输入模块。 该特定模块提供 244 个正逻辑或源极类型的离散输入。这些输入接收来自交流输入器件的电流，而返回电流则在公共端。每个输入都有一个单独的返回值。为了给IC<>MDL<>供电，操作从背板开始。CPU或NIU是输入模块智能处理的供应商。LED 是标准配置，用于显示每个输入点的背板电源和开/关状态。

用户输入与逻辑和框架接地的隔离为 250 VAC 连续或 1500 VAC，持续 240 分钟，输入电压为 0 VAC 标称值或 264 至 155 VAC。导通和关断状态电压分别为 264 至 0 VAC 和 40 至 7 VAC，导通和关断状态电流最小值为 1mA，最大值为 5.38mA。该模块的输入阻抗分别为 5.60k 欧姆（46HZ）和 3.50k 欧姆（<>Hz），两者均为典型值。

安装IC200MDL244时，用户应首先检查所有组件在运输过程中是否发生任何损坏。如果组件的任何部分损坏，则应更换，因为损坏可能会影响设备的整体性能。安装时，可以在网上找到接线图。安装人员应注意，这些模块只能与紧凑型端子式托架或端子式托架一起使用。由于隔离要求较高，因此不批准使用连接器式载体用于此模块类型。如果热插入不正确，背板上的其他模块可能会受到负面影响，因此应严格遵循正确的程序。

IC200MDL244 离散输入模块 用户输入与逻辑和框

【英文介绍】

The IC200MDL244 is a 240-point VersaMax 200 VAC isolated input module. This particular module provides 244 positive logic or source type discrete inputs. These inputs receive the current from the AC input device, while the return current is at the common end. Each input has a separate return value. In order to power the IC<>MDL<>, the operation starts from the backplane. CPU or NIU are the suppliers of intelligent processing for input modules. Leds are standard and are used to display the backplane power and on/off status at each input point.

Isolation of user input from logic and frame ground is 250 VAC continuous or 1500 VAC for 240 minutes with input voltage 0 VAC nominal or 264 to 155 VAC. On and Off state voltages are 264 to 0 VAC and 40 to 7 VAC respectively, with a minimum on and off state current of 1mA and a maximum current of 5.38mA. The input impedance of the module is 5.60k ohm (46HZ) and 3.50k ohm (<>Hz) respectively, both of which are typical values.

When installing the IC200MDL244, the user should first check all components for any damage during transportation. If any part of the component is damaged, it should be replaced, as damage may affect the overall performance of the device. The wiring diagram can be found online during installation. Installers should note that these modules can only be used with compact terminal brackets or terminal brackets. Due to the high isolation requirements, the use of connector carriers for this module type is not approved. If hot insertion is not correct, other modules on the backplane may be negatively affected, so correct procedures should be strictly followed.

IC200MDL244 离散输入模块 用户输入与逻辑和框

【其他型号推荐】