IC200CHS003 连接器式载体I/O 提供快速连接

【产品详情】

IC200CH003是由GE Fanuc自动化制造的连接器式载体I/O。IC200CH003 I/O 载体重 0.113 千克，配有一个 36 针连接器，用于连接输入/输出电缆。该载体为一个输入/输出模块的背板通信、安装和现场布线提供了条件。您可以找到一个模块闩锁孔，用于将模块固定到托架上。该托架还提供快速连接，用于连接多达 32 个输入/输出点和 4 个公共电源连接。

在导轨安装过程中，IC200CH003 I/O 托架可轻松卡入 DIN 导轨上，尺寸为：7.5 mm x 35 mm。 为了提供EMC保护，DIN必须电气接地。它们还必须具有导电和耐腐蚀的表面处理。现场接线连接直接在连接器样式本身上完成，借助压接到电线末端的触点。 I/O 设备可以直接连接到插入 I/O 端子。 为了安装预接线连接电缆，将电缆连接器放置在位于托架上的连接器上，然后向下按压，直到闩锁与连接器啮合。

要卸下电缆，必须握住连接器并将其压在闩锁上以松开连接器。有时，由于环境温度高，操作设备可能会变热。发生这种情况时，在处理连接器时要小心。建议不要直接触摸它。还要避开裸露的连接器引脚。提供用于制造定制电缆的连接器套件，并配有连接器和盖板、6 个大触点、2 个螺钉和 36 个小触点。IC200CH003载波可用于所有 VersaMax 模块，但以下模块除外，因为它们具有高隔离要求：

IC200MDL144带电压输入 240 VAC 4点隔离模块

IC200MDD850 混合 240 VAC 隔离式 4 点

输出继电器 2.0A 隔离 8 点模块

I/O 设备可以连接到IC200CHS003载体上的插入 I/O 端子。通过电缆连接到IC200CHS003连接器式托架。可用的电缆包括 IC200CBL105 电缆（2 个连接器，0.5 米，无屏蔽）、IC200CBL110 电缆（2 个连接器，1 米，无屏蔽）、IC200CBL120 电缆（2 个连接器，2 米，无屏蔽）和 IC200CBL230 电缆（1 个连接器，3 米，无屏蔽）。连接器上有一个槽口，用于指示引脚方向。GE Fanuc 提供连接器套件，用于构建定制电缆。该套件的部件号为 IC200ACC304。由于隔离要求，IC200CHS003托架可用于所有 Versamax I/O 模块，但以下模块除外：IC200MDL144、IC200MDL244 和 IC200MDD850 模块。IC200CHS003载波可适应以下电流水平：8 安培的电源和接地电流，以及 2 安培的点电流。该模块可以承受高达 300 伏交流电的电压瞬变。

IC200CHS003 连接器式载体I/O 提供快速连接

【英文介绍】

The IC200CH003 is a connector carrier I/O manufactured by GE Fanuc Automation. The IC200CH003 I/O carrier weighs 0.113 kg and is equipped with a 36-pin connector for connecting input/output cables. The carrier provides conditions for backplane communication, installation and field wiring of an input/output module. You can find a module latch latch hole for attaching the module to the bracket. The bracket also offers fast connections for connecting up to 32 input/output points and 4 common power connections.

The IC200CH003 I/O bracket can easily snap into the DIN rail during rail installation and is 7.5 mm x 35 mm in size. To provide EMC protection, DIN must be electrically grounded. They must also have a conductive and corrosion-resistant surface finish. Field wiring connections are made directly on the connector style itself, with the help of contacts crimped to the end of the wire. I/O devices can be connected directly to insert I/O terminals. To install the pre-wired connection cable, place the cable connector over the connector located on the carrier and press down until the latch engages the connector.

To remove the cable, you must hold the connector and press it against the latch to release the connector. Sometimes, operating equipment may become hot due to high ambient temperatures. When this happens, be careful when handling the connector. It is recommended not to touch it directly. Also avoid exposed connector pins. Connector kits are available for manufacturing custom cables and come with connectors and cover plates, 6 large contacts, 2 screws and 36 small contacts. The IC200CH003 carrier can be used in all VersaMax modules except for the following modules due to their high isolation requirements:

IC200MDL144 4-point isolation module with voltage input 240 VAC

IC200MDD850 Hybrid 240 VAC isolated 4-point

Output relay 2.0A isolated 8-point module

The I/O device can be connected to the insert I/O terminal on the IC200CHS003 carrier. Connect to IC200CHS003 connector bracket by cable. Available cables include IC200CBL105 cable (2 connectors, 0.5 m, no shielding), IC200CBL110 cable (2 connectors, 1 m, no shielding), IC200CBL120 cable (2 connectors, 2 m, no shielding), and IC200CBL120 cable (2 connectors, 2 m, no shielding). Unshielded) and IC200CBL230 cable (1 connector, 3 m, unshielded). There is a notch on the connector to indicate the pin direction. GE Fanuc offers connector kits for building custom cables. The kit's part number is IC200ACC304. Due to isolation requirements, the IC200CHS003 bracket can be used for all Versamax I/O modules except the following: IC200MDL144, IC200MDL244, and IC200MDD850 modules. The IC200CHS003 carrier can accommodate the following current levels: 8 amps of supply and ground current, and 2 amps of point current. The module can withstand voltage transients of up to 300 volts AC.

IC200CHS003 连接器式载体I/O 提供快速连接

【其他型号推荐】