GE Fanuc IC697MDL940  继电器输出模块

【产品详情】

技术规格

额定电压： 120/240 VAC 或 5/24/125 VDC

输出数量： 16 （8 - 表格 C 和 8 表格 A）

最大负载电流： 每个模块 16 安培，每组 4 安培（A 型）

所需电流： 750毫安

频率： 47-63 Hz（仅限交流电）

直流电源： 是的

IC697MDL940是 90-70 系列可编程逻辑控制器 （PLC） 模块，特别是继电器输出模块，共有十六 （16） 个继电器输出通道。具体来说，它有八 （8） 个 C 型触点输出和八 （8） 个 A 型或常开 （N.O.） 个，分为两 （2） 组，每组四 （4） 个 A 型触点。该模块的额定电压为 120/240 VAC 或 5/24/125 VDC，交流负载的最大功耗为 480 VA，直流负载的最大功耗为 60 瓦。它的最大额定负载电流为 2.0 安培，从 5 到 265 VAC（47-63 Hz）;2.0 安培，5 至 30 VDC;0 至 2 VDC 为 31.125 安培，0 至 2 VDC 为 31.150 安培，仅适用于模块最小负载电流为 10 mA 时的 A 型触点输出。每个输出通道的开和关信号转换的最大响应时间为 10 ms，与感性负载一起使用时，开关频率为每分钟 20 个周期。该模块的输出继电器为固定线圈、移动电枢型，输出触点由银合金制成，最大接触电阻为 0.2 欧姆，机械操作的预期触点寿命为 20,000,000 次，电阻感性负载下的预期触点寿命为 1,000,000 次电气操作。IC697MDL940的每个输出都安装有一个 3 安培保险丝，用作缓冲电路的内置通道保护，缓冲电路由 47 欧姆电阻器和电容值为 0.015 μfd 的电容器组成。

IC697MDL940输出继电器模块是GE发那科设计制造的输出继电器模块。该模块通常与 GE 90-70 系列的 PLC 设备一起使用，并配备额定电流为 3 安培的保险丝进行保护。该模块的典型触点寿命为 300,000 至 1,000,000 次操作，电阻负载的最大负载电流为 0.1 至 2 安培，感性负载的最大负载电流为 0.05 至 1 安培。这种特殊的 GE Fanuc 模块专为交流和直流操作而设计，它包括 120 至 240 伏交流电或 5、24 或 125 伏直流电的工作电压额定值。该模块有 16 个输出，工作频率为 47 至 63 赫兹（仅适用于交流电压）。输出点的配置包括在表格 C 中配置的 8 个点和在表格 A 中配置的相同数量的点。Form C 中的输出点是隔离的，其他点分为 2 组。

GE Fanuc IC697MDL940输出继电器模块的隔离电压额定值为 1500 伏，对于感性负载，其开关频率为每分钟 20 个周期。该模块在 1 伏交流电下的最大输出电流泄漏为 120 毫安，每个模块的最大负载电流为 16 安培或每组 4 安培。IC697MDL940模块的额定电流为 750 毫安。该模块的响应时间为 10 毫秒，交流负载的最大额定功率为 480 伏安，直流负载的最大额定功率为 60 瓦。IC697MDL940模块具有银合金触点，最大电阻额定值为 0.2 欧姆。该模块有一个固定的线圈继电器，带有一个移动的电枢。

GE Fanuc IC697MDL940  继电器输出模块

【英文介绍】

Technical specification

Rated voltage: 120/240 VAC or 5/24/125 VDC

Number of outputs: 16 (8 - Form C and 8 Form A)

Maximum load current: 16 amps per module, 4 amps per group (Type A)

Required current: 750 MA

Frequency: 47-63 Hz (AC only)

Dc power supply: Yes

The IC697MDL940 is a 90-70 series programmable logic controller (PLC) module, specifically the relay output module, with a total of sixteen (16) relay output channels. Specifically, it has eight (8) Type C contact outputs and eight (8) Type A or normally open (N.O.), divided into two (2) groups of four (4) type A contacts per group. The module is rated at 120/240 VAC or 5/24/125 VDC, with a maximum power consumption of 480 VA for AC loads and 60 watts for DC loads. It has a maximum rated load current of 2.0 amps, from 5 to 265 VAC (47-63 Hz); 2.0 amps, 5 to 30 VDC; 31.125 amps from 0 to 2 VDC and 31.150 amps from 0 to 2 VDC are available only for Type A contact output with a module minimum load current of 10 mA. The maximum response time of the on and off signal conversion for each output channel is 10 ms, and the switching frequency is 20 cycles per minute when used with inductive loads. The module has an output relay of fixed coil, moving armature type, output contact made of silver alloy, maximum contact resistance of 0.2 ohms, expected contact life of 20,000,000 times for mechanical operation and 1,000,000 times for electrical operation under resistive inductive load. Each output of the IC697MDL940 is fitted with a 3-amp fuse that serves as built-in channel protection for a buffer circuit consisting of 47 ohm resistors and capacitors with a capacitance value of 0.015 μfd.

The IC697MDL940 output relay module is an output relay module designed and manufactured by GE Fanuc. The module is typically used with the GE 90-70 series PLC equipment and is protected by a fuse rated at 3 amps. The module has a typical contact life of 300,000 to 1,000,000 operations with a maximum load current of 0.1 to 2 amps for resistive loads and 0.05 to 1 amp for inductive loads. This special GE Fanuc module is designed for AC and DC operation and includes an operating voltage rating of 120 to 240 volts AC or 5, 24 or 125 volts DC. The module has 16 outputs and operates at 47 to 63 Hz (AC voltage only). The configuration of the output points consists of the 8 points configured in Table C and the same number of points configured in Table A. The output points in Form C are isolated, and the other points are divided into two groups.

The GE Fanuc IC697MDL940 output relay module has an isolation voltage rating of 1500 volts and a switching frequency of 20 cycles per minute for inductive loads. The module has a maximum output current leakage of 120 mA at 1 volt AC and a maximum load current of 16 amps per module or 4 amps per group. The IC697MDL940 module has a rated current of 750 MA. The module has a response time of 10 milliseconds and a maximum power rating of 480 volt-amps for AC loads and 60 watts for DC loads. The IC697MDL940 module has silver alloy contacts and a maximum resistance rating of 0.2 ohms. The module has a fixed coil relay with a moving armature.

GE Fanuc IC697MDL940  继电器输出模块

【其他型号推荐】